Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Is my cartridge too new to reset?
#1
I don't know how best to describe my cartridge.  It came with the printer which I purchased in April 2016.  It has the white "screw" in the center so it may be opened and refilled.  This is the error I am getting when trying to use the reset sketch at https://github.com/voltivo/davinci_filam...et_arduino

Testing connection to Da Vinci EEPROM CHIP
Da Vinci EEPROM found...
Reading the Davinci EEPROM Contents...
(success)
00: 5840480000303040C0D00000C0D00000 [email protected]@........
10: D0005800504840403030303000000000 [email protected]@0000....
20: 0000000030000000F8F8F8F8A850A850 ....0........P.P
30: 883050A8C80800000000001000E800E0 .0P.............
40: 5840480000303040C0D00000C0D00000 [email protected]@........
50: D0005800504840403030303000000000 [email protected]@0000....
60: 0000000030000000F8F8F8F8A850A850 ....0........P.P
70: 883050A8C0D00000A850A85078100800 .0P......P.Px...
(success)
Updating EEPROM...
(failure)
(failure)
(failure)
(failure)
(failure)
(failure)
(failure)
(failure)
(failure)
(failure)
(failure)
(failure)
Dumping Content after modification...
(success)
00: 5840480000303040C0D00000C0D00000 [email protected]@........
10: D0005800504840403030303000000000 [email protected]@0000....
20: 0000000030000000F8F8F8F8A850A850 ....0........P.P
30: 883050A8C0D000000000001000E800E0 .0P.............
40: 5840480000303040C0D00000C0D00000 [email protected]@........
50: D0005800504840403030303000000000 [email protected]@0000....
60: 0000000030000000F8F8F8F8A850A850 ....0........P.P
70: 883050A8C0D00000A850A85078100800 .0P......P.Px...


Has anyone else run into this?
Reply
#2
From what I have seen the first line should be something like this:

00: 5A4147000034325380A9030080A90300 ZAG..42S........

Notice how the line starts with ZAG.   I believe this is the color setting or maybe the material type.  However, my output starts with:

00: 5840480000303040C0D00000C0D00000 [email protected]@........

It is almost a totally different format.  Since the resetter failed I am curious if anyone else has or has had this problem?
Reply
#3
This is a cartridge for a 3D printer not an HP Deskjet. I believe you have misposted.
Reply
#4
0: 5A4147000034325380A9030080A90300 ZAG..42S........

Notice how the line starts with ZAG.   I believe this is the color setting or maybe the material type.  However, my output starts with:

00: 5840480000303040C0D00000C0D00000 [email protected]@........ 3d printing mumbai pune - fdm technology
Reply
#5
(06-09-2017, 12:45 PM)3dtech Wrote: 0: 5A4147000034325380A9030080A90300 ZAG..42S........

Notice how the line starts with ZAG.   I believe this is the color setting or maybe the material type.  However, my output starts with:

00: 5840480000303040C0D00000C0D00000 [email protected]@........ 3d printing mumbai pune - fdm technology

It seems like maybe you have a bad connection to the cartridge. I've seen poor connections cause issues where the cartridge could be read but not written to. Honestly, it's kind of hard to support reading and writing cartridges as virtually no one is doing it anymore compared to just installing better firmware. Best of luck.

Kieth
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)