Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
"was received but is an invalid choice" from resetter
#1
Hello everyone,

I'm using Da Vinci 1.0A with stock firmware updated in november 2015. I use arduino Uno to reset my fillament to 240m, I did that about 10 times now, no problems with resetting length but, now i bought some PLA fillament and I wanted to change some parameters of my filament chip but my resetter just shows this message every time i try to change any parameters other than serial number/ length:
Quote: Menu options
1 = eeprom read
2 = reset eeprom
3 = read eeprom then set temps, filament length and increment serial number

Testing connection to Da Vinci EEPROM CHIP

Da Vinci EEPROM found...
Reading the Davinci EEPROM Contents...
(success)
00: 5A415A000034423780A9030080A90300 ZAZ..4B7........
10: D2005A00544847423033393700000000 ..Z.TXXXX397....
20: 0000000034000000FFFFFFFFAA55AA55 ....4........U.U
30: 883355AA0F0300000000001004ED00E0 .3U.............
40: 5A415A000034423780A9030080A90300 ZAZ..4B7........
50: D2005A00544847423033393700000000 ..Z.XXXXX397....
60: 0000000034000000FFFFFFFFAA55AA55 ....4........U.U
70: 883355AA80A90300AA55AA55A7060B00 .3U......U.U....

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

was received but is an invalid choice
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

Menu options
1 = eeprom read
2 = reset eeprom
3 = read eeprom then set temps, filament length and increment serial number

Testing connection to Da Vinci EEPROM CHIP

(success)
Updating EEPROM...
(success)
(success)
(success)
(success)
(success)
(success)
(success)
(success)
(success)
(success)
(success)
(success)
Testing connection to Da Vinci EEPROM CHIP

Da Vinci EEPROM found...
Reading the Davinci EEPROM Contents...
(success)
00: 5A415A000034423780A9030080A90300 ZAZ..4B7........
10: D2005A00544847423033393800000000 ..Z.TXXXX398....
20: 0000000034000000FFFFFFFFAA55AA55 ....4........U.U
30: 883355AA80A903000000001004ED00E0 .3U.............
40: 5A415A000034423780A9030080A90300 ZAZ..4B7........
50: D2005A00544847423033393800000000 ..Z.XXXXX398....
60: 0000000034000000FFFFFFFFAA55AA55 ....4........U.U
70: 883355AA80A90300AA55AA55A7060B00 .3U......U.U....

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

was received but is an invalid choice
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

Menu options
1 = eeprom read
2 = reset eeprom
3 = read eeprom then set temps, filament length and increment serial number

Testing connection to Da Vinci EEPROM CHIP

Da Vinci EEPROM found...
Reading the Davinci EEPROM Contents...
(success)

What i have to do to change my filament chip from beeing detected as ABS and turn it into PLA one?
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)